Diode Dynamics fog light fit… not quite there

7145 Views 55 Replies 19 Participants Last post by chrisjp20, 5 d ago

englishsteel

Discussion Starter · Jan 13, 2022

3

Just a couple photos of the tight fit of the Diode Dynamics current fit for our Ascents. Too tight to properly mount w/o cutting a lot. After a chat and some photos sent (great service BTW) they are sending new (their standard) bezel versus the round one. Will update later after final install.

Automotive parking light Vehicle Hood Automotive tire Grille

Land vehicle Tire Wheel Automotive tire Vehicle

Automotive lighting Hood Automotive tire Automotive tail & brake light Motor vehicle

See less See more

Reactions: 2

1 - 20 of 56 Posts

HeyChris

· #2 · Jan 13, 2022

That's a bummer... Glad DD is on top of this.

C.

Reactions: 2

pdxltd

· #3 · Jan 13, 2022 (Edited)

englishsteel said:
Just a couple photos of the tight fit of the Diode Dynamics current fit for our Ascents. Too tight to properly mount w/o cutting a lot. After a chat and some photos sent (great service BTW) they View attachment 15113
View attachment 15112
View attachment 15111
are sending new (their standard) bezel versus the round one. Will update later after final install.

There was some talk of this on the Modded Ascent Facebook page and a few people said they had to trim the lower plastic to get the lights to fit, this picture was one owners solution. I am about to buy these so let us know if the new set fits better.

Grille Automotive tire Automotive lighting Hood Alloy wheel

See less See more

Reactions: 3

scooby

· #4 · Jan 14, 2022

Oh thats good to know. I didnt realize you needed to do some trimming in order for them to fit properly. I have a set coming in soon and would like to know if I need to ask em to make any changes to my order before it ships.

Reactions: 2

Ey31

· #5 · Jan 16, 2022

I just push mine as far back as possible. The other way is to trim the bezel on the light as it doesn't do anything.

Reactions: 1

englishsteel

Discussion Starter · #6 · Jan 17, 2022

8

The “standard” bezel is the way to go… installation a breeze! Thanks to DD for sending a free set. I’ll call them tomorrow in hopes they update their fit and recommendations! Since I had a premium I had to cut the opening on the cover… I just followed the line around the fake opening. Hope this was helpful!

See less See more

Reactions: 5

scooby

· #7 · Jan 17, 2022

Awesome! Thanks for the follow up! Did you go with the Pro, Sport or Max?

Reactions: 1

Luis Padilla

· #8 · Jan 17, 2022

Nice job on the install.Looks like they need to be aimed lower.

Reactions: 1

englishsteel

Discussion Starter · #9 · Jan 17, 2022

scooby said:
Awesome! Thanks for the follow up! Did you go with the Pro, Sport or Max?

Wife bought me for the Sport for Christmas… I wanted the Pro

Reactions: 1

englishsteel

Discussion Starter · #10 · Jan 17, 2022

Luis Padilla said:
Nice job on the install.Looks like they need to be aimed lower.

Good call… agreed!

Merope

· #11 · Jan 17, 2022

I like these.

www.rallyinnovations.com

2019+ Subaru Ascent Light Conversion [SU-WMA-LCN-22]

-Signature required upon delivery- Note: Pigtail adapter only for H11 bulbs and vehicles that have the factory foglight option. Replace OEM fog lights with Baja Designs S2 LEDs (Link) Built specifically for this car model Simple bolt-on installation Material: 14-Gauge stainless steel...

www.rallyinnovations.com

www.rallyinnovations.com

Reactions: 2

AEONFLUX

· #12 · Jan 17, 2022

englishsteel said:
The “standard” bezel is the way to go… installation a breeze! Thanks to DD for sending a free set. I’ll call them tomorrow in hopes they update their fit and recommendations! Since I had a premium I had to cut the opening on the cover… I just followed the line around the fake opening. Hope this was helpful!

Why are you guys putting amber lights on your subarus

AlphaXrayPapa

· #13 · Jan 18, 2022 (Edited)

Merope said:
I like these...

I think I'd prefer to go that route myself, if only because the two lamps fit the Ascent foglamp opening better than the quad setup. Which is absolutely not meant as a dig towards anyone with this setup including the OP.

As far as selective yellow lighting goes, here's a good article that explains some advantages: Daniel Stern Lighting Consultancy and Supply

Reactions: 3

AEONFLUX

· #14 · Jan 18, 2022

AlphaXrayPapa said:
I think I'd prefer to go that route myself, if only because the two lamps fit the Ascent foglamp opening better than the quad setup. Which is absolutely not meant as a dig towards anyone with this setup including the OP.

As far as selective yellow lighting goes, here's a good article that explains some advantages: Daniel Stern Lighting Consultancy and Supply

Thank you. Was just curious why non off roaders use amber so thats a fast response and interesting

HeyChris

· #15 · Jan 18, 2022

Amber, FTW...

I am thoroughly enjoying my SS3 Max Ambers...

Not my photo...

Automotive lighting Natural landscape Road surface Asphalt Car

See less See more

Reactions: 3

scooby

· #16 · Jan 18, 2022

@HeyChris Did you end up switching to the standard bezels as well?

HeyChris

· #17 · Jan 18, 2022

My Gen5 Outback is plug and play. Round bezels.
(No Ascent in the garage, yet?)

Reactions: 1

scooby

· #18 · Jan 18, 2022 (Edited)

Got cha! I know your post said that wasnt your photo, but is that pretty much how bright the maxes are? Thats what I ordered, and I'm just hoping the output justifies the price.

Reactions: 1

HeyChris

· #19 · Jan 19, 2022

It does.....

You can always experiment with different lens....

Driving.
Driving/Flood.....

But no Driving/Fog.... 🥸

scooby

· #20 · Jan 19, 2022

Oh thats going to be so awesome. Been trying to stay patient, but your post didnt help.

Reactions: 2

1 - 20 of 56 Posts